Active Elements Concrete preparation cleaner surface etch 1 Gallon concentrated biodegradable
Active Elements Concrete preparation cleaner surface etch 1 Gallon concentrated biodegradable
Active Elements Concrete preparation cleaner surface etch 1 Gallon concentrated biodegradable
Product Overview
Installation instructions at ubqind.com
UBQ Industries - Active Elements™ Surface Etch
Concrete cleaner and surface etch for prepping concrete surfaces
Active Elements™ - Surface Etch is a concentrated phosphoric acid-based etching solution with special additives
that have been developed to safely prepare concrete surfaces before applying concrete paint and sealers. Active Elements -
Surface Etch gently removes topical laitance and creates a porous surface to increase the penetration of concrete
paint and sealers.
It produces minimal fumes, is biodegradable and safe for use near grass and plants.
Use on:
• Garage floor prior to epoxy coating or sealer
• Any concrete prior to applying a pigmented stain, concrete paint, overlay, resurface, micro topping, stamped overlay
• Shiny power troweled concrete prior to Concrete Acid Stain application
• Any concrete prior to applying a pigmented stain, concrete paint, overlay, resurface, micro topping, stamped overlay
• Shiny power troweled concrete prior to Concrete Acid Stain application
Dilution Ratios: (with clean water):
• When prepping for Sealers, Pigmented Stains, Epoxy Coatings, Overlays or Resurfacers
• When prepping for Sealers, Pigmented Stains, Epoxy Coatings, Overlays or Resurfacers
(1) Part Active Elements - Surface Etch to (4) Parts Clean water
• When prepping a very smooth floor for Concrete Acid Stain
(1) Part Active Elements - Surface Etch to (10) Parts Clean water
Coverage:
Apply at a rate of 100 square feet per gallon of solution.
Apply at a rate of 100 square feet per gallon of solution.
Application
1. Sweep or blow off the surface to remove loose debris.
1. Sweep or blow off the surface to remove loose debris.
2. Remove any paint or sealers with Active Elements - Paint Strip.
3. Treat grease and/or oil spots with Active Elements - Degrease.
4. Allow surface to dry.
5. Apply Active Elements - Surface Etch using a sprinkler can. The solution will fizz on contact with the
concrete.
Be sure to completely and evenly saturate the concrete with the etching solution.
Always start at the lowest point and work your way up to ensure fresh acid is being applied to dry
concrete.
Scrub the solution into the surface with a stiff bristle broom until the fizzing stops then rinse the surface
with water. Do not allow the Active Elements - Surface Etch solution to dry on the concrete.
If additional surface porosity is needed repeat Step 5.
6. Neutralize the surface using Active Elements - Neutralize (8oz in 5 gallons water) and scrub with a stiff
bristle broom to scrub in the neutralizing solution then rinse with water. Use a wet vacuum to collect
residue and waste water. Dispose in accordance with local, state, and federal regulations
7. Thoroughly scrub the surface. Interior floors require the use of a floor machine (buffer) with a black pad,
sanding screen or coatings removal pad. Exterior concrete preparation requires the use of a pressure
washer.
Safety
Always use appropriate safety equipment including but not limited to, goggles, face shield, rubber gloves,
chemical resistant clothing or apron, and chemical respirator. Consult product MSDS for additional safety
information. Do not permit contact with eyes or skin. Do not breathe vapors, ventilate area during mixing or
application. Close container immediately after each use. Store upright in a tightly closed container away from
combustible material and sources of heat. Never transfer to an unmarked container. Do not reuse empty
container, empty containers may contain hazardous product residues. Before use, review the Material Safety
Data Sheet for further information, including health effects.
FIRST AID
Skin - Wash thoroughly with soap and water. Discard affected clothing and footwear.
Skin - Wash thoroughly with soap and water. Discard affected clothing and footwear.
Eyes - Flush with water immediately. Hold eyelids apart while flushing material out thoroughly with large
amounts of water.
Seek Medical Attention Immediately!
Ingestion - Give several glasses of water. Seek Medical Attention Immediately!
Inhalation - Move to fresh air.
Warranty
This warranty is made in lieu of all other warranties, either expressed or implied. Before application the User
shall determine the suitability of the product for his/her intended use and User assumes all risks and liabilities
whatsoever in connection therewith. Neither seller nor manufacturer has any knowledge or control concerning
the purchaser’s use of this product and no warranty is made as to the results of any use. The Manufacturer
and/or Seller warrants that if any goods supplied prove defective in material the sole obligation shall be to
replace said product. Any claim of defective product must be received in writing within one (1) year from date of
shipment. Neither Manufacturer nor Seller shall assume any liability for injury, loss, or damage resulting from
use of this product.
DO NOT TAKE INTERNALLY. KEEP OUT OF REACH OF CHILDREN.
| Brand: | Active Elements |
|---|---|
| Isin: | IF80YZNJN9T4 |
Out of Stock
In Stock
Backordered
Out of Stock
IBspot Buyer Protection
Shop confidently on IBspot, receive your item as described or your money back for eligible orders. Learn Program Terms
Product Overview
Installation instructions at ubqind.com
UBQ Industries - Active Elements™ Surface Etch
Concrete cleaner and surface etch for prepping concrete surfaces
Active Elements™ - Surface Etch is a concentrated phosphoric acid-based etching solution with special additives
that have been developed to safely prepare concrete surfaces before applying concrete paint and sealers. Active Elements -
Surface Etch gently removes topical laitance and creates a porous surface to increase the penetration of concrete
paint and sealers.
It produces minimal fumes, is biodegradable and safe for use near grass and plants.
Use on:
• Garage floor prior to epoxy coating or sealer
• Any concrete prior to applying a pigmented stain, concrete paint, overlay, resurface, micro topping, stamped overlay
• Shiny power troweled concrete prior to Concrete Acid Stain application
• Any concrete prior to applying a pigmented stain, concrete paint, overlay, resurface, micro topping, stamped overlay
• Shiny power troweled concrete prior to Concrete Acid Stain application
Dilution Ratios: (with clean water):
• When prepping for Sealers, Pigmented Stains, Epoxy Coatings, Overlays or Resurfacers
• When prepping for Sealers, Pigmented Stains, Epoxy Coatings, Overlays or Resurfacers
(1) Part Active Elements - Surface Etch to (4) Parts Clean water
• When prepping a very smooth floor for Concrete Acid Stain
(1) Part Active Elements - Surface Etch to (10) Parts Clean water
Coverage:
Apply at a rate of 100 square feet per gallon of solution.
Apply at a rate of 100 square feet per gallon of solution.
Application
1. Sweep or blow off the surface to remove loose debris.
1. Sweep or blow off the surface to remove loose debris.
2. Remove any paint or sealers with Active Elements - Paint Strip.
3. Treat grease and/or oil spots with Active Elements - Degrease.
4. Allow surface to dry.
5. Apply Active Elements - Surface Etch using a sprinkler can. The solution will fizz on contact with the
concrete.
Be sure to completely and evenly saturate the concrete with the etching solution.
Always start at the lowest point and work your way up to ensure fresh acid is being applied to dry
concrete.
Scrub the solution into the surface with a stiff bristle broom until the fizzing stops then rinse the surface
with water. Do not allow the Active Elements - Surface Etch solution to dry on the concrete.
If additional surface porosity is needed repeat Step 5.
6. Neutralize the surface using Active Elements - Neutralize (8oz in 5 gallons water) and scrub with a stiff
bristle broom to scrub in the neutralizing solution then rinse with water. Use a wet vacuum to collect
residue and waste water. Dispose in accordance with local, state, and federal regulations
7. Thoroughly scrub the surface. Interior floors require the use of a floor machine (buffer) with a black pad,
sanding screen or coatings removal pad. Exterior concrete preparation requires the use of a pressure
washer.
Safety
Always use appropriate safety equipment including but not limited to, goggles, face shield, rubber gloves,
chemical resistant clothing or apron, and chemical respirator. Consult product MSDS for additional safety
information. Do not permit contact with eyes or skin. Do not breathe vapors, ventilate area during mixing or
application. Close container immediately after each use. Store upright in a tightly closed container away from
combustible material and sources of heat. Never transfer to an unmarked container. Do not reuse empty
container, empty containers may contain hazardous product residues. Before use, review the Material Safety
Data Sheet for further information, including health effects.
FIRST AID
Skin - Wash thoroughly with soap and water. Discard affected clothing and footwear.
Skin - Wash thoroughly with soap and water. Discard affected clothing and footwear.
Eyes - Flush with water immediately. Hold eyelids apart while flushing material out thoroughly with large
amounts of water.
Seek Medical Attention Immediately!
Ingestion - Give several glasses of water. Seek Medical Attention Immediately!
Inhalation - Move to fresh air.
Warranty
This warranty is made in lieu of all other warranties, either expressed or implied. Before application the User
shall determine the suitability of the product for his/her intended use and User assumes all risks and liabilities
whatsoever in connection therewith. Neither seller nor manufacturer has any knowledge or control concerning
the purchaser’s use of this product and no warranty is made as to the results of any use. The Manufacturer
and/or Seller warrants that if any goods supplied prove defective in material the sole obligation shall be to
replace said product. Any claim of defective product must be received in writing within one (1) year from date of
shipment. Neither Manufacturer nor Seller shall assume any liability for injury, loss, or damage resulting from
use of this product.
DO NOT TAKE INTERNALLY. KEEP OUT OF REACH OF CHILDREN.
| Brand: | Active Elements |
|---|---|
| Isin: | IF80YZNJN9T4 |
Installation instructions at ubqind.com
UBQ Industries - Active Elements™ Surface Etch
Concrete cleaner and surface etch for prepping concrete surfaces
Active Elements™ - Surface Etch is a concentrated phosphoric acid-based etching solution with special additives
that have been developed to safely prepare concrete surfaces before applying concrete paint and sealers. Active Elements -
Surface Etch gently removes topical laitance and creates a porous surface to increase the penetration of concrete
paint and sealers.
It produces minimal fumes, is biodegradable and safe for use near grass and plants.
Use on:
• Garage floor prior to epoxy coating or sealer
• Any concrete prior to applying a pigmented stain, concrete paint, overlay, resurface, micro topping, stamped overlay
• Shiny power troweled concrete prior to Concrete Acid Stain application
• Any concrete prior to applying a pigmented stain, concrete paint, overlay, resurface, micro topping, stamped overlay
• Shiny power troweled concrete prior to Concrete Acid Stain application
Dilution Ratios: (with clean water):
• When prepping for Sealers, Pigmented Stains, Epoxy Coatings, Overlays or Resurfacers
• When prepping for Sealers, Pigmented Stains, Epoxy Coatings, Overlays or Resurfacers
(1) Part Active Elements - Surface Etch to (4) Parts Clean water
• When prepping a very smooth floor for Concrete Acid Stain
(1) Part Active Elements - Surface Etch to (10) Parts Clean water
Coverage:
Apply at a rate of 100 square feet per gallon of solution.
Apply at a rate of 100 square feet per gallon of solution.
Application
1. Sweep or blow off the surface to remove loose debris.
1. Sweep or blow off the surface to remove loose debris.
2. Remove any paint or sealers with Active Elements - Paint Strip.
3. Treat grease and/or oil spots with Active Elements - Degrease.
4. Allow surface to dry.
5. Apply Active Elements - Surface Etch using a sprinkler can. The solution will fizz on contact with the
concrete.
Be sure to completely and evenly saturate the concrete with the etching solution.
Always start at the lowest point and work your way up to ensure fresh acid is being applied to dry
concrete.
Scrub the solution into the surface with a stiff bristle broom until the fizzing stops then rinse the surface
with water. Do not allow the Active Elements - Surface Etch solution to dry on the concrete.
If additional surface porosity is needed repeat Step 5.
6. Neutralize the surface using Active Elements - Neutralize (8oz in 5 gallons water) and scrub with a stiff
bristle broom to scrub in the neutralizing solution then rinse with water. Use a wet vacuum to collect
residue and waste water. Dispose in accordance with local, state, and federal regulations
7. Thoroughly scrub the surface. Interior floors require the use of a floor machine (buffer) with a black pad,
sanding screen or coatings removal pad. Exterior concrete preparation requires the use of a pressure
washer.
Safety
Always use appropriate safety equipment including but not limited to, goggles, face shield, rubber gloves,
chemical resistant clothing or apron, and chemical respirator. Consult product MSDS for additional safety
information. Do not permit contact with eyes or skin. Do not breathe vapors, ventilate area during mixing or
application. Close container immediately after each use. Store upright in a tightly closed container away from
combustible material and sources of heat. Never transfer to an unmarked container. Do not reuse empty
container, empty containers may contain hazardous product residues. Before use, review the Material Safety
Data Sheet for further information, including health effects.
FIRST AID
Skin - Wash thoroughly with soap and water. Discard affected clothing and footwear.
Skin - Wash thoroughly with soap and water. Discard affected clothing and footwear.
Eyes - Flush with water immediately. Hold eyelids apart while flushing material out thoroughly with large
amounts of water.
Seek Medical Attention Immediately!
Ingestion - Give several glasses of water. Seek Medical Attention Immediately!
Inhalation - Move to fresh air.
Warranty
This warranty is made in lieu of all other warranties, either expressed or implied. Before application the User
shall determine the suitability of the product for his/her intended use and User assumes all risks and liabilities
whatsoever in connection therewith. Neither seller nor manufacturer has any knowledge or control concerning
the purchaser’s use of this product and no warranty is made as to the results of any use. The Manufacturer
and/or Seller warrants that if any goods supplied prove defective in material the sole obligation shall be to
replace said product. Any claim of defective product must be received in writing within one (1) year from date of
shipment. Neither Manufacturer nor Seller shall assume any liability for injury, loss, or damage resulting from
use of this product.
DO NOT TAKE INTERNALLY. KEEP OUT OF REACH OF CHILDREN.
Processing Time
- We process and ship orders Monday through Friday, excluding holidays.
- Most orders are processed within 1–3 business days, depending on product availability.
- Processing time does not include delivery time, which varies based on your location and the product’s shipping origin.
Shipping Coverage
We currently ship to addresses within the United States only.
Products may ship from:
- Our U.S. warehouses, or
- Our international fulfillment centers (including Korea, Japan, China, Australia, Mexico, Canada, the United Kingdom, and the EU).
Each product page clearly displays the “Ships From” location before checkout.
Shipping Methods & Estimated Delivery
| Shipping Method | Estimated Delivery | Cost |
|---|---|---|
| Free Shipping (US) | 5–10 business days | Free, available on eligible items |
| Standard Shipping (US to US by Item) | 5–10 business days | $6.50 for the first item, $2.00 each additional |
| Standard Shipping (From US Warehouse by Weight) | 3–7 business days | Starts at $6.50, increasing by $2 for every additional 4 oz (0.25 lb) up to 1 lb, then by $4 for each additional pound beyond 1 lb. |
| Extended Delivery (Ships from Overseas Warehouse) | 10–20 business days | $14.50 for the first item, $2.00 each additional |
Shipping costs vary by product weight, quantity and origin. Exact rates and delivery estimates are displayed on each product page and confirmed during checkout.
Free Shipping
We offer free standard shipping on select products or during promotional periods. Availability of free shipping will be displayed on the product page and at checkout.
Carriers
We primarily use USPS and UPS for U.S. deliveries. Items shipped from international warehouses may be handled by partner carriers depending on the country of origin.
Import Duties & Taxes
All import duties and taxes for goods imported into the United States are included in the product price. There are no hidden fees or additional charges at checkout.
Tracking & Notifications
Every order is fully trackable. You will receive a tracking number via email once your order ships. If your order ships in multiple packages, each package will have its own tracking number. If you don’t receive a shipping confirmation immediately, your order is still being processed and will arrive within the estimated timeframe shown at checkout.
You can track your shipment anytime using the Track Your Order page on our website.
Order Changes & Cancellations
If you need to modify or cancel an order, please contact our customer support team as soon as possible. Orders can only be canceled before they ship. Once shipped, cancellations are not possible, but you may request a return after the item is delivered.
Contact: support@ibspot.com
Item Not Received
If your tracking number shows “Delivered” but you haven’t received your package:
- Check with your local USPS or UPS office.
- Confirm that the shipping address provided was correct.
- If the issue remains unresolved, contact support@ibspot.com for assistance.
Damaged or Lost Parcels
If your package arrives damaged or fails to arrive, please contact us immediately. For deliveries to P.O. boxes, ibspot is not responsible for damage caused by weather, temperature, or theft.
Customer Support
For any questions about shipping, tracking, or delivery, our customer support team is here to help.
Email: support@ibspot.com
We’re always happy to help.
Please read our policy carefully before making a purchase.
We aim to ensure every customer has a smooth and transparent experience with ibspot.com.
Order Cancellation Policy
Customers may request to cancel an order before it has been shipped.
Once the package has been shipped, cancellations are no longer possible; however, you may still request a return after receiving your order.
How to Request a Cancellation
You can contact us through:
- Email: support@ibspot.com
- Contact Form: Submit a request through our Contact Us page
Please submit your cancellation request as soon as possible after placing the order to allow us to process it before shipment.
Return Policy
We accept returns for most items within 30 days of delivery for a full refund.
To be eligible for a return:
- The item must be unused, in the same condition as received, and in its original packaging.
- A tracking number must be provided to confirm the return shipment.
Non-Returnable Items
Certain products cannot be returned, including:
- Perishable goods (for example, food, flowers, newspapers, magazines)
- Intimate or sanitary goods
- Hazardous materials or flammable liquids/gases
- Gift cards
- Downloadable software
- Some health and personal care items
Partial Refunds (If Applicable)
Partial refunds may be granted in specific situations, such as:
- Books with obvious signs of use
- Opened CDs, DVDs, software, or vinyl records
- Items not in their original condition, damaged, or missing parts not due to our error
- Items returned more than 30 days after delivery
How to Return an Item
To initiate a return, please contact us at support@ibspot.com with your order number and details about the product you wish to return.
Our team will provide you with return instructions and a prepaid return label.
Shipping Cost for Returns
Please contact us before returning any item.
We will provide a free return shipping label.
If a return is sent back without prior contact or without our provided label, we cannot be held responsible for return shipping costs.
For items valued over $75, we recommend using a trackable shipping service or purchasing shipping insurance.
We cannot guarantee that we will receive your returned item if shipped independently.
Refund Processing
Once your return is received and inspected:
- In-store returns are refunded to the original form of payment or issued as a gift card.
- Mail-in returns using our prepaid label are refunded to the original payment method within 3–5 business days after we receive your return.
Please allow:
- 5–7 business days for the return to reach our Returns Center.
- An additional 3–10 business days for your bank to post the refund to your account.
Damages, Issues & Claims
Please inspect your order immediately upon receipt.
If you receive a defective, damaged, or incorrect item, contact us right away at support@ibspot.com.
We’ll evaluate the issue promptly and make it right.
Product Claims
Before purchasing, please review product details carefully.
If there is a problem with your order upon arrival, visit our Support Center or contact us directly to arrange return shipping or replacement.
Exchanges
We do not process direct exchanges.
The fastest way to get what you need is to return the original item and place a new order once your return is accepted.
Return Address
IBSPOT Return Center
15 Sawmill Ln
Dover Plains, NY 12522
United States
Customer Support
Our support team is available 24/7 to assist with cancellations, returns, or general inquiries.
Email: support@ibspot.com
Contact Form: Contact Us page
Oops!
Sorry, it looks like some products are not available in selected quantity.